Astronergy 715W Bifacial Solar Panel

Astronergy 715W Bifacial Solar Panel Overview

The Astronergy 715W Bifacial Solar Panel is designed for solar projects that need high power output from each installed module. Its 715W rated capacity helps reduce the number of panels required for a given DC array capacity compared with lower-wattage modules, subject to the project’s electrical design and available installation space.

The panel uses N-Type monocrystalline TOPCon 4.0 cells and a bifacial construction. Its front side captures direct sunlight, while the rear side can collect reflected and scattered light from suitable surfaces. The additional rear-side contribution varies with ground reflectivity, mounting height, row spacing, shading and other installation conditions.

With a 23.0% module efficiency, this model can be useful where installation area and DC capacity need careful planning. Its 1500V DC maximum system rating supports appropriately designed high-voltage solar arrays, provided all string and equipment limits are respected.

The panel is suitable for consideration in commercial rooftops, industrial solar projects and ground-mounted installations. Final selection should account for inverter input-current limits, string voltage, mechanical support and the project’s operating conditions.

Key Features and Benefits

N-Type TOPCon 4.0 Cell Technology

The panel uses N-Type monocrystalline TOPCon 4.0 technology. Its rated power of 715W and module efficiency of 23.0% make it suitable for installations seeking substantial output per module.

For buyers, module efficiency helps indicate how effectively the available panel area converts sunlight into electrical power under standard test conditions. Actual daily energy generation will depend on sunlight, temperature, orientation, shading, dust and system losses.

For more technical information, visit the Astronergy Solar Panel Official Website.

Bifacial Energy Generation

The bifacial design allows the module to generate electricity from both sides. Its 80% ± 5% bifaciality rating describes the rear-side power response relative to the front-side response under the applicable test conditions.

Rear-side energy gain is not a fixed percentage for every installation. A reflective ground surface, suitable mounting arrangement and reduced rear shading can help improve the contribution from the back of the panel.

High Module Efficiency

The module provides 23.0% efficiency at its 715W rated output. Higher efficiency can help a project achieve more installed DC capacity within a limited panel area, although roof layout, access pathways, structural limits and electrical design remain important.

Low Power Degradation

The panel has a maximum first-year power degradation of 1.0% and maximum annual degradation of 0.4% for years 2–30. These limits support long-term performance planning. Actual output can still vary with operating conditions, maintenance and the applicable warranty terms.

Dual-Glass Construction

The module features 2.0 mm front glass and 2.0 mm rear glass, along with an anodized silver aluminium frame. This construction is relevant to bifacial installations, where rear-side light collection is part of the system design.

The listed maximum mechanical test loads are 5400 Pa on the front and 2400 Pa on the rear. Correct mounting hardware, support spacing and installation practices remain essential.

Best For

The Astronergy 715W Bifacial Solar Panel can be considered for:

• Commercial solar systems requiring high DC capacity.
• Industrial installations with suitable structural and electrical infrastructure.
• Ground-mounted solar projects where rear-side light collection can be improved.
• Large rooftops with sufficient space and structural capacity.
• Solar installers and project developers planning high-output modules.
• Projects where module efficiency, long-term degradation and bifacial performance are important selection factors.

When Another Panel May Be Better

This panel may not be the most practical option for every installation.

• Small roofs with limited usable space or difficult panel access may need a different module layout.
• Existing systems may have inverter current, voltage or connector limits that do not match the selected panel.
• Installations with closely spaced rows, heavy rear shading or low-reflectivity surfaces may receive limited additional energy from the bifacial design.
• Projects with mounting structures designed for smaller modules should verify dimensions, weight and wind-loading requirements before selecting this panel.

The correct choice depends on the complete solar system design, not wattage alone.

Cell and Module Technology

The Astronergy 715W model belongs to the N8 CHSM66N(DG)/F-BH bifacial series and uses N-Type monocrystalline TOPCon 4.0 technology.

Its 132-cell configuration is arranged in a 6 × 22 layout. The module measures 2384 × 1303 × 33 mm and weighs 38 kg, so installers should check handling requirements, mounting compatibility and available installation space.

The dual-glass construction supports the module’s bifacial design. To make effective use of rear-side generation, the mounting arrangement should allow reflected and scattered sunlight to reach the back of the panel.

Technical Specifications

Performance and Degradation

Long-term solar production depends on the initial module output, temperature, installation conditions, cleaning and the gradual reduction in power over time.

For this model, the maximum first-year degradation is 1.0%, followed by a maximum annual degradation of 0.4% during years 2–30. The published performance curve indicates approximately 87.40% power retention at year 30.

The Pmax temperature coefficient of -0.29%/°C indicates that power output generally decreases as cell temperature rises above the standard test temperature, all else being equal. Good airflow beneath the modules and an appropriate mounting arrangement can help manage operating temperature.

These ratings are useful for project planning, but they do not guarantee a particular annual energy yield. Site conditions, system design and the applicable warranty terms should be considered together.

Performance Considerations for Pakistan

Solar installations in Pakistan can experience high summer temperatures, dust accumulation and seasonal changes in sunlight. These conditions influence the real-world output of solar modules.

For this panel, consider the following installation points:

• Temperature management: Use a suitable mounting arrangement that allows airflow behind the module.
• Dust and cleaning: Inspect panels periodically and clean them according to safe installation practices and local conditions.
• Bifacial mounting: Where possible, avoid unnecessary rear-side shading and consider the reflectivity of the surface below the panel.
• Electrical design: Account for module voltage, current and temperature effects when configuring strings.
• Mechanical support: Verify the mounting structure, clamps and site-specific wind and load requirements.
• Inverter matching: Check the inverter’s maximum DC voltage, MPPT range, operating current and short-circuit current limits before installation.

These steps help installers design a system around the module’s actual characteristics rather than relying on the wattage rating alone.

Astronergy 715W Bifacial Solar Panel Price in Pakistan

The final cost of a solar project depends on the number of panels required, mounting equipment, inverter selection, cabling, protection devices, installation and transportation. Bulk orders may also have different commercial terms.

For buyers comparing the astronergy 715w bifacial solar panel price in pakistan, it is useful to check the exact model, panel condition, applicable warranty and seller availability before placing an order.

Customers in Lahore and other parts of Pakistan can contact Hajvery Solar Energy to discuss panel quantities, current availability and project requirements.

Tier 1, A-Grade and Product Authenticity

Buyers evaluating Astronergy solar panels should distinguish brand identity, module specifications and the actual condition of the supplied product.

Do not assume that every panel is A-Grade or that a particular shipment has a specific certification status without verifying the relevant product and stock details.

For astronergy solar panels verification online, use an official verification channel where available, and confirm the product label, serial information and applicable warranty details with the seller. Product authenticity and stock condition should be checked for the actual panel being purchased.

Hajvery Solar Product Verification

Before ordering the Astronergy 715W Bifacial Solar Panel, confirm the following:

• The product label matches the intended 715W bifacial model.
• The panel’s physical condition and serial information are checked.
• The applicable product and performance warranty terms are understood.
• The selected inverter can accommodate the module’s voltage and current characteristics.
• The mounting arrangement supports the module’s dimensions and weight.
• Rear-side clearance is suitable if bifacial energy generation is an important project objective.

Hajvery Solar Energy can help buyers discuss product details and solar-system requirements before purchase.

You can verify your Astronergy Solar Panel through Hajvery Solar Energy’s solar panel verification page:

Astronergy Panel Verification Link

Warranty

The Astronergy 715W Bifacial Solar Panel comes with a 15-year product warranty and a 30-year linear power warranty.

The product warranty and linear power warranty cover different aspects of the module and should not be treated as interchangeable. Buyers should confirm the applicable warranty terms, coverage conditions and claim procedure before purchase.

Frequently Asked Questions

1. What is the Astronergy 715W Bifacial Solar Panel price in Pakistan?

The current price of the Astronergy 715W Bifacial Solar Panel in Pakistan is Rs. 27,170 per panel. Contact Hajvery Solar Energy to confirm availability and order quantities.

2. What is the efficiency of the Astronergy 715W solar panel?

The module has a rated efficiency of 23.0% at its 715W power rating under standard test conditions.

3. Is the Astronergy 715W panel bifacial?

Yes. It can generate electricity from both the front and rear sides. Additional rear-side production depends on reflected light, mounting height, surface reflectivity and shading.

4. What technology does this panel use?

It uses N-Type monocrystalline TOPCon 4.0 cell technology with a 132-cell configuration.

5. What are the dimensions and weight of this panel?

The module measures 2384 × 1303 × 33 mm and weighs 38 kg. Check mounting structure capacity and handling arrangements before installation.

6. What is the warranty of the Astronergy 715W Bifacial Solar Panel?

It has a 15-year product warranty and a 30-year linear power warranty. Applicable terms and claim requirements should be confirmed before ordering.

7. Can this panel work with any solar inverter?

No universal compatibility should be assumed. The inverter’s maximum DC voltage, MPPT operating range, input-current limits and short-circuit current limits must be checked against the module and proposed string design.

8. Where can I find the astronergy 715w datasheet?

Contact Hajvery Solar Energy for the relevant product technical information and confirm that the model code matches the panel you intend to purchase.

Buy Astronergy 715W Bifacial Solar Panel from Hajvery Solar Energy

Hajvery Solar Energy offers solar-product purchasing assistance for residential, commercial and industrial customers. If you are comparing astronergy 715w bifacial solar panel specifications, ask about the exact model, warranty terms, electrical compatibility and current availability before ordering.

Visit Hajvery Solar Energy at 280K Block J-1, Johar Town, Lahore, or contact the team to discuss your solar project and panel requirements.

To explore more options, visit the Astronergy Panels in Pakistan.